 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| INTEGRATED CIRCUITS 74ALS86 Quad 2-Input exclusive-OR gate Product specification IC05 Data Handbook 1996 Jul 01 Philips Semiconductors Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 DESCRIPTION The 74ALS86 contain four independent 2-input Exclusive-OR gates. A common application is a true/complement element. If one input is held Low, the signal on the other input will be reproduced in true form at the output. If one input is held High, the signal on the other input will be reproduced inverted at the output. TYPICAL PROPAGATION DELAY 6.0ns TYPICAL SUPPLY CURRENT (TOTAL) 3.9mA PIN CONFIGURATION 1A 1B 1Y 2A 2B 2Y 1 2 3 4 5 6 7 14 VCC 13 4B 12 4A 11 4Y 10 3B 9 8 3A 3Y TYPE 74ALS86 GND ORDERING INFORMATION ORDER CODE DESCRIPTION COMMERCIAL RANGE VCC = 5V 10%, Tamb = 0C to +70C 74ALS86N 74ALS86D DRAWING NUMBER SOT27-1 SOT108-1 SC00010 14-pin plastic DIP 14-pin plastic SO INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS nA, nB nY Data inputs Data outputs DESCRIPTION 74ALS (U.L.) HIGH/LOW 1.0/1.0 20/80 LOAD VALUE HIGH/LOW 20A/0.1mA 0.4mA/8mA NOTE: One (1.0) ALS unit load is defined as: 20A in the High state and 0.1mA in the Low state. LOGIC SYMBOL IEC/IEEE SYMBOL 1 2 =1 3 1 2 4 5 9 10 12 13 4 6 1A 1B 2A 2B 3A 3B 4A 4B 5 9 8 1Y 2Y 3Y 4Y 10 12 11 3 VCC = Pin 14 GND = Pin 7 6 8 11 13 SC00011 SC00037 LOGIC DIAGRAM 1A 1B 2A 2B 3A 3B 4A VCC = Pin 14 GND = Pin 7 4B 1 2 4 5 9 10 12 13 3 1Y FUNCTION TABLE INPUTS nA L L 3Y OUTPUT nB L H L H nY L H H L 6 2Y 8 H H H = High voltage level L = Low voltage level 11 4Y SC00038 1996 Jul 01 2 853-0596 01670 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL VCC VIN IIN VOUT IOUT Tamb Tstg Supply voltage Input voltage Input current Voltage applied to output in High output state Current applied to output in Low output state Operating free-air temperature range Storage temperature range PARAMETER RATING -0.5 to +7.0 -0.5 to +7.0 -30 to +5 -0.5 to VCC 16 0 to +70 -65 to +150 UNIT V V mA V mA C C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL VCC VIH VIL IIk IOH IOL Tamb Supply voltage High-level input voltage Low-level input voltage Input clamp current High-level output current Low-level output current Operating free-air temperature range 0 PARAMETER MIN 4.5 2.0 0.8 -18 -0.4 8 +70 NOM 5.0 MAX 5.5 V V V mA mA mA C UNIT DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL VOH VO OL VIK II IIH IIL IO ICC PARAMETER High-level output voltage Low-level Low level output voltage Input clamp voltage Input current at maximum input voltage High-level input current Low-level input current Output current3 TEST CONDITIONS1 MIN VCC10%, VIL = MAX, VIH = MIN, IOH = -0.4mA VCC = MIN, VIL = MAX, , , VIH = MIN VCC = MIN, II = IIK VCC = MAX, VI = 7.0V VCC = MAX, VI = 2.7V VCC = MAX, VI = 0.5V VCC = MAX, VO = 2.25V VCC = MAX, VI = 4.5V -30 3.9 IOL = 4mA IOL = 8mA VCC - 2 0.25 0.35 -0.73 0.40 0.50 -1.5 0.1 20 -0.1 -112 5.9 LIMITS TYP2 UNIT MAX V V V V mA A mA mA mA Supply current (total) NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25C. 3. The output conditions have been chosen to produce a current that closely approximate one half of the true short-circuit output current, IOS. 1996 Jul 01 3 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION Tamb = 0C to +70C VCC = +5.0V 10% CL = 50pF, RL = 500 MIN tPLH tPHL tPLH tPHL Propagation delay nA or nB to nY Propagation delay nA or nB to nY Waveform 2 (other input Low) Waveform 1 (other input High) 2.0 2.0 2.0 2.0 MAX 12.0 12.0 12.0 12.0 ns ns UNIT AC WAVEFORMS For all waveforms, VM = 1.3V. nA, nB VM tPHL VM tPLH VM VM nA, nB VM tPLH VM tPHL VM VM nY nY SC00039 SC00013 Waveform 1. Propagation Delay for Data to Output Waveform 2. Propagation Delay for Data to Output TEST CIRCUIT AND WAVEFORMS VCC NEGATIVE PULSE VIN PULSE GENERATOR RT D.U.T. VOUT 90% VM 10% tTHL (tff) CL RL tw VM 10% tTLH (tr ) 0.3V 90% AMP (V) tTLH (tr ) 90% tTHL (tf ) AMP (V) 90% VM tw 10% 0.3V Test Circuit for Totem-pole Outputs POSITIVE PULSE 10% VM DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. Input Pulse Definition INPUT PULSE REQUIREMENTS Family Amplitude VM 74ALS 3.5V 1.3V Rep.Rate 1MHz tw 500ns tTLH 2.0ns tTHL 2.0ns SC00005 1996 Jul 01 4 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1 1996 Jul 01 5 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 1996 Jul 01 6 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 DEFINITIONS Data Sheet Identification Objective Specification Product Status Formative or in Design Definition This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Preliminary Specification Preproduction Product Product Specification Full Production Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 1997 All rights reserved. Printed in U.S.A. Philips Semiconductors 1996 Jul 01 7 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1 1996 Jul 01 8 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 1996 Jul 01 9 Philips Semiconductors Product specification Quad 2-input exclusive-OR gate 74ALS86 NOTES 1996 Jul 01 10 |
Price & Availability of 74ALS86N
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |